ALLEN BRADLEY PLC
ALLEN BRADLEY
MODEL NO: MICROLOGIX 1200 SERIES C
INPUT: 14 & OUTPUT: 10
COMMUNICATION PROTOCOL: RS 232
TO OPEN THE SOFTWARE
Then select CPU model
FILE – NEW – SELECT (MICROLOGIX 1200 SERIESC)
Hardware configuration:
DIGITAL INPUT/DIGITAL OUTPUT (14/10):
INPUT: I: 0/0 to I: 0/13
OUTPUT: O: 0/0 to O: 0/9
INTEGER: N7:0 N7:255
FLOAT: F8:0 F8:255
BINARY: B3:0/0 B3:0/15
.
.
.
.
B3:255/0 B3:255/15
CONTROL REGISTER: R6:0 R6:255
JUMP: Q2:0 Q2:99
SUB ROUTINE: U:3 U:99
STRING: ST9:0 ST9:255
ANALOG (2/2)
INPUT: I:1.0 AND I:1.1
OUTPUT: O:1.0 AND O:1.1USER:
NO CONTACT
NC CONTACT
LOAD
LATCH COIL
UN LATCH COIL
BIT:
1.ONE SHOT
2.ONE SHOT RISING
3.ONE SHOT FALLING
1.ONE SHOT:
It produces it pulse during off state to on state. It does not have output bit
ONE SHOT RISING:
It produces its pulse during of state to on state.
ONE SHOT FALLING:
It produces its output pulse during on state to off state
Timer and Counter Instructions
If You Want to: Use This Instruction:
Delay turning on an output TON
Delay turning off an output TOF
Time an event retentively RTO
Count up CTU
Count down CTD
Reset the accumulated value
and status bits of a timer or
counter.(Not used with
TOF timers.) RES
COMPARE INSTRUCTION:
If You Want to Use This Instruction
Test whether two values are equal (=) EQU
Test whether one value is not equal
to a second value (><) NEQ
Test whether one value is less than
a second value (<) LES
Test whether one value is less than
or equal to a second value (<=) LEQ
Test whether one value is greater
than a second value (>) GRT
Test whether one value is greater
than or equal to a second value (=>) GEQ
Test portions of two values to see
whether they are equal MEQ
Test whether one value is within the
limit range of two other values LIM
COMPUTE / MATH:
If You Want to Use This Instruction
Add two values ADD
Subtract two values SUB
Multiply one value by another MUL
Divide one value by another DIV
Change the sign of the source
value and place it in thedestination NEG
If You Want to Use This Instruction
Set all bits of a word to zero CLR
Convert an integer value to BCD TOD
Convert a BCD value to an integer
value FRD
SQUARE ROOT (SQR):
Find the square root of a value
GRAY CODED DECIMAL(GCD):
This output instruction converts the Gray code Source to integer and places it in the Destination. On a True rung, this instruction sets the value of the Destination to the integer value corresponding to the Gray code Source. If the Gray code input is negative (high bit set), the destination is set to 32767 and the overflow flag is set. The GCD instruction only operates on Word operands.
MOVE / LOGICAL INSTRUCTION:
If You Want to Use This Instruction
Move the source value to the destination MOV
Move data from a source location to a
selected portion of the destination MVM
Perform an AND operation AND
Perform an inclusive OR operation OR
Perform an Exclusive Or operation XOR
Perform a NOT operation NOT
MOVE:
When rung conditions preceding this instruction are true, the MOV instruction moves a copy of the source to the destination each scan. The original value remains intact and unchanged in its source location.
MASKED MOVE:
When rung conditions are true, the MVM instruction moves data from a source location to a destination, and allows portions of the destination data to be masked by a separate word. Data at the source address passes through the mask to the destination address. As long as the rung remains true, the instruction moves the same data each scan.
CLEAR:
When rung conditions are true, this output instruction sets all the bits in a word to zero. The destination must be a word address.
AND: When rung conditions are true, sources A and B of this output instruction are ANDed bit by bit and stored in the destination.
PROGRAM CONTROL:
If You Want to Use This Instruction
Jump forward/backward to a
corresponding label instruction JMP, LBL
Jump to a designated subroutine and return JSR, SBR, RET
Enable or inhibit a master control zone
in your ladder program MCR
Truncate program scan TND
JUMP:
When the rung condition for this output instruction is true, the processor jumps forward or backward to the corresponding label instruction (LBL) and resumes program execution at the label. More than one JMP instruction can jump to the same label. Jumping forward to a label saves program scan time by omitting a program segment until needed. Jumping backward lets the controller execute program segments repeatedly.
JUMP TO SUBROUTINE:
When rung conditions are true for this output instruction, it causes the processor to jump to the targeted subroutine file. You can only jump to the first instruction in a subroutine. Each subroutine must have a unique file number (decimal, 3-255).
SUBROUTINE PAGE:
TO CREATE THE NEW SUBROUTINE PAGE:
PROGRAM FILES – RIGHT CLICK NEW
TEMPORARILY END (TND):
Use this instruction to progressively debug a program, or conditionally omit the balance of your current program file or subroutines.
MASTER CONTROL RESET (MCR):
An input instruction is programmed on the rung of the first MCR to control rung logic continuity. When the rung goes "false" all non-retentive outputs within the controlled zone are disabled. When the rung goes "true" all rungs are scanned according to their normal rung conditions (disregarding the zone control instruction).
ADVANCED MATH INSTRUCTION:
If You Want to: Use This Instruction:
Swap the low and high bytes
of a specified number of words SWP
Scale a value to a range determined
by creating a linear relationship SCP
Calculate the absolute value of a number ABS
Decoder functions DCD
Encoder function ENC
DECODER(DCD):
When rung conditions are true, the DCD instruction decodes a 4-bit value (0-16) in the source word and turns on a bit in the destination word that corresponds to the decoded value. For example, if bits 0-3 of a source word are 0110, then bit 6 in the destination word is set. The table below provides full details.
ENCODER (ENC):
This output instruction searches the source from the lowest to the highest bit and looks for the first set bit. The corresponding bit position is written to the destination as an integer.
SCALE WITH PARAMETER(SCL):
This output instruction consists of six parameters. Parameters may be integer, long, floating point (Floating point is only supported in the SLC 5/03, 5/04, and 5/05; not in the MicroLogix 1200 and 1500 processors.), or immediate data values or addresses containing values. The Input value is scaled to a range determined by creating a linear relationship between input min and max values and scaled min and max values. The scaled result is returned to the address indicated by the output parameter.
SWAP (SWP):
Use the swap instruction to swap the low and high bytes of a specified number of words in a bit, integer, ASCII, or string file. The instruction consists of two parameters, a source and a length.
ABSOLUTE VALUE (ABS):
This output instruction consists of two parameters, a source and a destination. When enabled it calculates the absolute value of the source and places the result in the destination.
Source can be a word address, an integer constant, floating point data element, or floating point constant.
0 comments:
Post a Comment